Stampin’ Up! Online Exclusives: Naturally Gilded Specialty DSP & Brilliant Wings Card

Card Measurements and Supply List for this project are found at the bottom of this blog post.

Starting March 1st Stampin’ Up! is adding a new Online Exclusives section to the Online Store. As a demonstrator I was able to pre-order a selection of the upcoming products including the beautiful Naturally Gilded Specialty Designer Series Paper. I created this lovely card using Gold Foil butterflies die cut from the Brilliant Wings dies and a gold embossed sentiment from the upcoming Irresistible Blooms stamp set.

161639
Naturally Gilded Specialty Designer Series Paper
$10.00
155523
BRILLIANT WINGS DIES
$44.00

Start with a Thick Very Vanilla cardstock card base. Cut a Gold Foil sheet panel and a Naturally Gilded Specialty Designer Series Paper panel. Attach the Designer Series Paper panel to the Gold Foil sheet panel with Stampin’ Seal. Wrap the panels with Gold & Vanilla Satin Edged ribbon using Stampin’ Seal to secure the ribbon’s ends to the back of the panels. Use glue or more Stampin’ Seal to add the wrapped panels to the card base.

Die cut out a Very Vanilla cardstock and a Gold Foil sheet label with the All That dies. Dust the Very Vanilla cardstock label with the Embossing Buddy powder and then stamp the sentiment from the Irresistible Blooms stamp set in Versamark, add gold embossing powder, tap off the excess, and then use the Heat Tool to melt the embossing powder. Cut the Gold Foil sheet label in half with paper snips. Use Stampin’ Seal to add the halves of the Gold Foil sheet label to the back of the heat embossed label. Use Stampin’ Dimensionals to add the labels to the right side of the card front overlapping the wrapped ribbon.

Die cut Gold Foil sheet butterflies with the Brilliant Wings dies. Use glue dots to add the butterflies to the card front. Add gold Brushed Metallic Adhesive – Backed Dots to the butterflies. Tie a bow with the Gold & Vanilla Satin Edged ribbon and use glue dots to add it to the left side of the labels overlapping the wrapped ribbon.

Cut a Very Vanilla cardstock inside panel to write your message and add stability. Add a strip of Naturally Gilded Specialty Designer Series Paper strip to the bottom of the inside panel and back of the card. Dust the Very Vanilla cardstock inside panel above the Specialty Designer Series Paper strip with the Embossing Buddy powder and then stamp the sentiment from the Irresistible Blooms stamp set in Versamark, add gold embossing powder (making sure it is only on over the sentiment), tap off the excess, and then use the Heat Tool to melt the embossing powder. Glue the inside panel into the card.

I added the Stampin’ Up! copyright stamp from the new Limited Edition stamp set to adhere to the Angel Policy.

Add a die cut Gold Foil sheet butterfly to the inside and back of the card to pull the theme through.

I hope you enjoyed my Naturally Gilded Specialty DSP & Brilliant Wings card. You can order the Brilliant Wings dies, the All That dies, and Gold Foil Sheets in my Online Store and order the Naturally Gilded Specialty Designer Series Paper and Irresistible Blooms stamp set starting March 1st.

Card Measurements:
Thick Very Vanilla cs card base – 11″ x 4 1/4″ scored at 5 1/2″.
Gold Foil sheet panel – 5 3/8″ x 4 1/8″.
Naturally Gilded Specialty DSP panel – 5″ x 3 3/4″ plus 1/2″ x 4″ strips.
Gold Foil sheet label layer – die cut with the All That dies and cut in half with paper snips.
Very Vanilla cs label – die cut with the All That dies.
Gold Foil sheet butterflies – die cut the Brilliant Wings dies.
Very Vanilla cs panel – 5 1/8″ x 3 7/8″.
Gold & Vanilla Satin Edged ribbon
DSP = Designer Series Paper
cs = cardstock

Product List
You can check out the new Stampin’ Up! Online Exclusives on my blog here.

Happy Crafting,

Stay Safe,

Christy

Find the Current Host Code & Ordering Special HERE.

Check out the Latest Stampin’ Up! Specials HERE.

Check out the Current Stampin’ Up! Catalogs HERE.

You can follow me on Instagram here.

Leave a comment